CONCEPT DEMO· Illustrative structure and copy for a Yixing rubber & plastics manufacturer· Placeholder data marked TO BE CONFIRMED
Home  /  Capabilities

What the plant can do — and what it cannot

A capability page that only lists strengths is a brochure. This page states the process routes, the equipment classes, and the work we would send elsewhere.

Process routes

RouteWhat it is forTypical strengthWhere it stops working
Compression mouldingFlat and shaped seals, thick sections, low to medium volumeLow tooling cost, tolerant of thick sectionsLong cycle times; flash and deflashing on intricate edges
Transfer mouldingIntricate shapes, inserts, sections that are hard to preformBetter dimensional control on complex geometryHigher tooling cost; pot and sprue waste
ExtrusionConstant cross-section profiles, cord, bulb and lip sealsVery low die cost, continuous lengthTight tolerances across the section; undercuts are not possible
Bonded / over-mouldingRubber-to-metal or rubber-to-plastic assembliesPart consolidation, defined stiffnessSubstrate preparation and bond control add cost and risk
Plastic parts (partner route)Rigid inserts, housings and low-volume plastic partsAvailable through a qualified partner, not made in this plantWarp, shrinkage and tooling ownership sit with the partner and are stated in the quotation
What we do not do in-house. Dynamic stiffness and transmissibility testing, accelerated ageing to automotive standards, and independent material certification are external. If your specification needs them, they are quoted as third-party work with the laboratory named — not absorbed into a vague "tested" claim.

Equipment classes

Counts and tonnages are placeholders until the client supplies the asset list. An equipment list is the fastest way for a buyer to judge what a plant can actually take on.

StageEquipmentWhy a buyer cares
MixingInternal mixer and open mill qty to confirmIn-house compound control vs buying ready-mixed stock
MouldingCompression presses, transfer presses, injection units tonnage to confirmMaximum part size and cavity count
ExtrusionHot and cold feed extruders, vulcanisation line to confirmProfile size range and output rate
ToolingIn-house or outsourced mould making to confirmTool lead time and cost, and who owns the tool
TestingTensile tester, hardness, ageing oven, projector / CMM to confirmWhich reports can be issued in-house vs external

From drawing to shipment

01 · REVIEW

Manufacturability

Geometry, tolerance stack, material callout and any standard named by the buyer. Output: a written review with open questions.

02 · QUOTE

Tooling and piece price

Tooling options with tool life stated, piece price at stated volumes, and the assumptions the price depends on.

03 · SAMPLE

First article

Samples with dimensional report and material batch record. Anything out of tolerance is reported, not shipped quietly.

04 · PRODUCE

Batch and inspect

Batch traceability, in-process checks and pre-shipment inspection against the agreed plan.

Buyer questions

What happens if you cannot hold the tolerance on my drawing?

We say so in the review, before tooling. Either the dimension is relaxed to a class the process can hold, or the part is re-routed to a different process, or we decline. Discovering it at first article is expensive for both sides.

Can I see the plant before placing an order?

Yes. Buyers or their agents are welcome to visit, and a video walkthrough can be arranged if travel is not practical. An audit checklist can be agreed in advance so the visit answers the questions that matter to you.

Do you do prototyping as well as production?

Yes. Prototype tooling, bridge tooling and production tooling are quoted as separate options with different tool life, so the buyer can decide how much to invest before the design is frozen.

What is your capacity?

Capacity is stated per process and per tooling route in the quotation, because it depends on machine allocation rather than a single plant-wide number. The figure on any page of this site marked TO BE CONFIRMED is a placeholder.

Ask a process question before you ask for a price

Tell us the part, the media and the tolerance. We will tell you which route fits and where the risk is.

Request a quote